diyobd2 car diagnostic tools

Program EWS4 key: Xprog+AVDI or VVDIProg+VVDI2?

diycar | 19 April, 2018 07:31

Here, I will show you two ways of BMW EWS4 new key programming, the first done with Xhorse tools (VVDI-Prog and VVDI2) and the second done with Xprog-M and AVDI key programmer.

alt

Option 1: Xhorse VVDI makes EWS4 keys

Option 2: Xprog + AVDI program EWS4 keys

Option 1: Xhorse VVDI makes EWS4 keys

Upload a video... show you the whole key programming procedure step by step

Step 1: VVDI Prog reads EWS4 eeprom data

Step 2: VVDI2 BMW programs a new key

Also, attach questions and answers that users frequently asked. Hope it’s useful.

Q: Can i make a x series key with the vvdi2 and how? (it’s x3 2004)

A: Yes ...it is ews4 (eeprom job )

 

Q: Taking the ecu out?

A: Not the ecu ...taking immo box out ...its a white box under the steering wheel same size as a pack of cigs.

 

Q: Do i need any adapter for that?

A: you just need open vvdi prog ,select ews4 and will show you the connections....solder it and you are good to read it

 

Q: And does it give you a key code like the cas’s

A: no , is it your first isn’t it?

 

Q: yes it is. Is this what i need?

alt

A: thats not for ews4...VVDI prog have its own EWS4 adapter, so does the AK90

I mean there is ews4 incircuit connect by vvdi prog. Look here:

 

Q: how is the procedure

A: Put the ESW4 module in the adapter and lock it

alt

To solder

alt

Option 2: Xprog-M + AVDI program EWS4 keys

Here, take BMW X3 E83 2006

step 1: Xprog-m reads the immobilizer block EWS4.4

So, get the immobilizer block from the car ...

alt

For this we remove the plastic protection above the gas and brake pedals.

alt

We lay down on the threshold, look up and see a white box, this is  EWS4.4 . Unscrew the nut on the right, loosen the nut on the left, remove the connector and take out the block.

alt

This immobilizer unit is assembled on a Motorola MC9S12D64 microcontroller , with a 2L86D mask .

alt

Since on BMW X3 E83 , we registered the key for the first time, it was initially mistakenly assumed that the six points to the right of the processor would be enough for us to read the firmware.

alt

However, Xprog-M , when reading eeprom 2L86D , issued the error:

  • Bootloader initialising error. Can not access BDM. Check BDM connection.

It became clear that the processor is "closed" and to read its firmware you will need a BDM adapter  1-002-0017 and, accordingly, another connection scheme.

alt

But, strictly speaking, this circuit is also MC9S12D64 (2L86D) + Xprog-M (BDM 1-002-0017) .

alt

Solder to the block ...

alt

... and read the firmware.

step 2: avdi Program key to EWS4.4 FROM BMW X3 E83

So, we have a dump, which means that it's up to the small thing to program the chip, which is in our key.

alt

To do this, get the AVDI (ABRITES Vehicle Diagnostic Interface)  and connect the Tag Key Programmer to it  .

alt

We launch the Tag Key Tool , select the Key Tool item and in the Vehicle Model field , select our option - BMW EWS4. PCF7935 or EML . As you can see, only 4 keys can be assigned to the car, well, or a chip.

alt

Click on the Load Dump button and select the dump that we counted from the processor. We tick the Key 3 PCF7935 / EML used and press the Prepare Key button . After that, the program asked:

  • Do you programming original BMW key (EML)? Press NO if you using PIT (PCF793x) transponder.
  • Translation:Do you want to program the original BMW key (EML)? Press NO if you are using a PIT (PCF793x) transponder. "

Click the No button .

alt

The process of programming the transponder begins, after which the window pops up:

  • Transponder programmed
  • Translation: Thetransponder is programmed

alt

Well, this looks like this programmed transponder.

Everything, the key is registered in the car. We checked that EWS4.4 gives permission to start the engine and programmed the radio channel

How to get bitting code with SEC-E9 key cutting machine

diycar | 12 April, 2018 05:44

There are three options to read get bitting code (also named key code) using SEC-E9 automatic key cutting machine.

What is bitting code?

The bitting code is the translated blind code which the locksmith actually uses to cut each blank key. Example: padlock blind code W123 translates to bitting code 25313, to which the locksmith would cut the key with his code machine by setting it to 25313.

What is SEC-E9 key cutting machine?

SEC-E9 Key Cutting Machine is used for cutting car keys and household keys. It covers cylinder and laser keys with adapters for other key styles.

SEC-E9 portable metal desktop air cooling fully automatic smart key cutting machine is able to cut standard keys and high security keys, such as BMW, VW, HONDA, OPEL,etc, SEC-E9 also supports to cut house keys, including dimple keys, tubular keys, single standard keys and motorcycle keys. Ford Tibbe keys and LDV keys are available to cut. SEC-E9 is a good choice for locksmith since you do not need to buy other small key cutting machines for house keys, just need to buy the corresponding clamps for different key types. Moreover, SEC-E9 can cut a new key without original key. It is the main difference from the traditional manual key cutting machine.

How to get key code using SEC-E9 key cutter?

Option 1: decoding the original key

 

Tab “decide” to enter the decoding page

Select the most right blue icon as sense key location and “round of”

alt alt alt alt

Check the original key can open the cylinder

Fix the original key on the top level of the clamp

Please pay attention to the key position

alt

Tab “decode” to start decoding the original key and get the bitting code

alt alt

Option 2: search key code

This is the key code for a Toyota Camry key

alt

Tab “code” and input “5-5-0-6-2” to get the bitting code

alt alt alt

 

Option 3: input bitting code directly

Tab “Input” and input bitting code you get from other ways, such as A cylinder, Lishi tool or InstaCode, etc.

alt alt alt

For more details of key cutting machine, please go to http://www.chinacardiags.com/producttags/key-cutting-machine.html

VVDI Key tool clone ID48 96bit model list

diycar | 12 April, 2018 05:05

VVDI Key tool supports all ID48 96bit clone up to 2017-18……success 100%.

 

Model

ID

Year

Skoda

Octavia

48

Up to 2017-18

Fabia

48

Up to 2017-18

Laura

48

Up to 2017-18

Superb

48

Up to 2017-18

Rapia

48

Up to 2017-18

Yeti

48

Up to 2017-18

Volkswagen

Polo

48

Up to 2017-18

Vento

48

Up to 2017-18

Ameo

48

Up to 2017-18

Jetta

48

Up to 2017-18

Passat

48

Up to 2017-18

Touareg

48

Up to 2017-18

Audi

A4/A6

48

Up to 2017-18

Q3/5/7

48

Up to 2017-18

TT/R8

48

Up to 2017-18

Fiat

Linea

48

Up to 2017-18

Punto

48

Up to 2017-18

Avventura

48

Up to 2017-18

Volvo

S60/80,XC70/90

48

Up to 2017-18

Honda

Accord (OLD)

48

Up to 2017-18

Chevrolet

Beat/Sail

48

Up to 2017-18

VVDI Key tool clone ID48 96bit authorization

Service: $250

Reliable source:

http://www.xhorsevvdi.com/wholesale/vvdi2-copy-48-transponder-96-bit-authorization.html

VVDI Key Tool

http://www.xhorsevvdi.com/wholesale/xhorse-vvdi-key-tool.html

Description:

VVDI Key Tool 48 Copy 96bitVVDI Key Tool user can buy a Clone 48 96bit since April 1st 1500 free points for calculations , this same as VVDi2  since 1.04.2018 all users who have 48 96 bit activation in VVDI2 can combine Keytool + VVDI2 and use Keytool to clone 48 as well 

Cloning cost 100 bonus points or 1 token each time.

How to bind VVDI2 with key tool to clone 96bit 48

FAQ : VVDI KEY TOOLBonus Points Reward System

Question 1: what the Bonus Points Reward System is?

The bonus point system is meant to reward you with points each time you use the Xhorse remotes.

Once you accumulate enough points they can be exchanged for freebies or money of software authorizations for other Xhorse programmers etc.

 

Question 2: How much points does VVDI Remote function give you?

From Xhorse normal-wire remote you get 25 bonus points.

From Xhorse-wireless remote you get 40 bonus points.

 

How to check the Xhorse Points?

The bonus points can be stored on the Xhorse points server by using Xhorse Upgrade Kit software.

The bonus points can be easily checked from the Xhorse Customer self-service system .

Question 3: How to collect the point? My points are 0.

maybe somebody use your remote before you get it ?

once you generate points from remote – you cannot get it again

simple check points via Upgrate Kit.

This from Xhorse vvdi Official site:VVDI Key tool clone ID48 96bit model list

 
Provided by Multiblog.net - easy blogging platform
P0wered by L1fe7ype - De51gn by Ba1earWe6